Prostar Services branded service truck in Wilson, NC
Prostar Services truck wrapped with the slogan Building Trust by Providing Results, parked at sunset in Wilson, NC
Google 5 stars
4.8 Star Rating | 330+ Google Reviews

No Heat Troubleshooting

Heat’s Out? Check These First

Prostar technician performing heating repair at a home in Wilson, NC

No Heat in Wilson, NC? Start Here

When the heat quits on a cold night, a good share of no-heat calls come down to something you can check yourself in about five minutes. Not all of them. But enough that it’s worth walking the list before you wait on anybody, including us.

Here’s the order we’d check things in, and the two situations where you should stop reading and pick up the phone.

Book Online

Stop and do this first

If you smell gas (a rotten egg or sulfur smell), leave the house now. Don’t flip switches, don’t unplug anything, and don’t use your phone inside. Get everyone out, then call your gas utility or 911 from outside. Call us after they’ve cleared it.

If your carbon monoxide alarm is going off, get everyone outside into fresh air and call 911. Carbon monoxide has no smell. Treat the alarm as real every time, even if everyone feels fine.

1. Check the Thermostat, Then Check It Again

It sounds too simple. It’s also one of the most common causes of a no-heat call.

  • Set to Heat, not Cool or Off. Easy to bump, easy to miss.
  • Set above room temperature. Push it up five degrees and see if the system kicks on.
  • Fan on Auto, not On. With the fan set to On, the blower runs constantly, including between heating cycles when it’s pushing room-temperature air. The house feels drafty and cold even though the heat is working.
  • Fresh batteries. A thermostat with dying batteries can hold its display and still stop talking to the system.
  • Blank screen? That’s usually batteries or a tripped breaker, not a dead furnace.

2. Check the Breaker

Find the breaker labeled for your furnace, air handler, or heat pump and look at it closely. A tripped breaker doesn’t always sit obviously in the middle. Push it fully off, then back on.

If it trips again right away, stop. Something is drawing current it shouldn’t, and resetting it over and over is how a small problem turns into an expensive one. That’s a call.

3. Check the Switch That Looks Like a Light Switch

Most furnaces and air handlers have a service switch mounted on or beside the unit, usually in a closet, attic, crawlspace, or garage. It looks exactly like an ordinary light switch, which is why people flip it off by accident. Make sure it’s on.

4. Check the Filter

A filter packed with dust chokes airflow. Modern systems have a safety that shuts things down before the heat exchanger overheats, so a dirty filter can show up as no heat.

Pull it out and hold it up to a light. If you can’t see light through it, replace it. In most eastern NC homes a one-inch filter needs changing every one to two months during the season, sooner with pets.

5. Check the Outdoor Unit if You Have a Heat Pump

A lot of homes around Wilson run heat pumps, and a heat pump needs its outdoor unit running in winter too. Go look at it.

  • Is the fan turning?
  • Is it clear of leaves, pine straw, and yard debris?
  • Is there ice on it? A light frost is normal. A solid shell of ice is not.

Steam rolling off it isn’t a problem. That’s the defrost cycle working the way it should. If that’s what you’re seeing, read heat pump frozen or steaming.

6. Check the Condensate Drain

High-efficiency furnaces produce water. If the drain clogs, a float switch shuts the system off on purpose to keep it from overflowing. Standing water around the unit or in the drain pan is a likely sign, and the drain line needs to be cleared.

When to Stop and Call

Call us and stop troubleshooting if any of these are true:

  • The breaker trips again after you reset it
  • You smell gas, or your CO alarm has sounded
  • The system starts and then shuts off again within a few minutes, over and over
  • You hear grinding, screeching, or a hard bang on startup
  • You’ve been through this list and still have no heat
  • It’s below freezing and the house temperature keeps dropping

What Happens When We Come Out

We answer 24/7, including nights, weekends, and holidays. A technician diagnoses the actual problem, explains what they found and what the repair costs, and doesn’t start work until you approve it. Learn more about our heater repair service in Wilson.

If the system is old enough that a repair doesn’t make sense, we’ll say so plainly and lay out both options. You decide. You can book online or call (252) 285-4050.

More Heating Help

No Heat FAQs for Wilson, NC Homeowners

Why is my heat blowing cold air?

Most often the thermostat fan is set to On instead of Auto, so the blower runs between heating cycles and pushes room-temperature air. On a heat pump, air in the mid-80s to mid-90s is normal and feels cool against your skin even though it’s heating the house.

Should I keep resetting the breaker if it trips?

No. Reset it once. If it trips again, something is wrong electrically and repeated resets can make the damage worse. Leave it off and call.

How cold is too cold to wait until morning?

If indoor temperatures are heading toward the 40s, or you have pipes on exterior walls or in a crawlspace, don’t wait. Freeze damage costs far more than an after-hours call.

Do you charge extra at night or on weekends?

Call us at (252) 285-4050 and we’ll tell you what the visit costs before we come out.

My heat works but some rooms are freezing. Is that the same problem?

Usually not. Uneven heating typically points to ductwork, insulation, or a system that’s the wrong size for the house rather than an outright failure. It’s worth having someone look, but it isn’t an emergency.

Technician sliding a new filter into a home furnace

Still No Heat? We Answer 24/7.

If you’ve worked through the checklist and the house is still cold, call Prostar. We’ll diagnose the problem and give you the price before any work starts.

Call Now (252) 285-4050